Page Pid Parameters Commissioning 4. P must be Page Vector Parameters Commissioning 4. Page Network Parameters Commissioning 4. See P Sleep Mode is active See P Page Fault Messages Troubleshooting and Diagnostics Fault Messages The messages below show how they will appear on the display when the drive trips. When looking at the Fault History P , the F. Page 37 Notes This manual is also suitable for: Show all Print page 1 Print document 38 pages. Rename the bookmark.
Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk. Do not bend any components and do not change any insulation distances during transport, handling, installation or maintenance. Do not touch any electronic components or contacts. This drive contains electrostatically sensitive components, which can easily be damaged by inappropriate handling.
Static control precautions must be adhered to during installation, testing, service and repair of this drive and associated options. Component damage may result if proper procedures are not followed.
This drive must be installed and configured in accordance with both national and international standards. It is neither a machine nor a device ready for use in accordance with European directives reference machinery directive and electromagnetic compatibility directive. It is the responsibility of the end user to ensure that the machine meets the applicable standards. When working on live drive controllers, applicable national safety regulations must be observed.
The electrical installation must be carried out according to the appropriate regulations e. While this document makes recommendations in regard to these items, national and local codes must be adhered to.
The documentation contains information about installation in compliance with EMC shielding, grounding, filters and cables. These notes must also be observed for CE-marked controllers. The manufacturer of the system or machine is responsible for compliance with the required limit values demanded by EMC legislation. The drive must not be used as a safety device for machines where there is a risk of personal injury or material damage. Emergency Stops, over-speed protection, acceleration and deceleration limits, etc.
The drive features many protection devices which are aimed at protecting the drive and the driven equipment by generating a fault and shutting the drive and motor down by removing power.
Mains power variances can also result in shutdown of the drive. When the fault condition disappears or is cleared, the drive can be configured to automatically restart. Operation in public supply networks Limitation of harmonic currents i.
CLim max is the maximum setting for P The CLim max value in the V column is used when P is set to 0. The drive output current or operating temperature may need to be limited as described below:. Drives must not be installed where subjected to adverse environmental conditions. Drives must not be installed where subjected to adverse environmental conditions such as: combustible, oily, or hazardous vapors or dust; excessive moisture; excessive vibration or excessive temperatures.
Severe damage to the drive can result if it is operated after a long period of storage or inactivity without reforming the DC bus capacitors. If input power has not been applied to the drive for a period of time exceeding three years due to storage, etc. This can result in premature failure of the capacitors if the drive is operated after such a long period of inactivity or storage.
In order to reform the capacitors and prepare the drive for operation after a long period of inactivity, apply input power to the drive for 8 hours prior to actually operating the motor. Hazard of electrical shock! Circuit potentials are up to VAC above earth ground. Capacitors retain charge after power is removed. Disconnect power and wait at least three minutes before servicing the drive.
Severe damage to the drive will result. Damage to the drive will result. Leakage current may exceed 3. Minimum size of the protective earth conductor shall comply with local safety regulations for high leakage current equipment. This clamp is typically located at the conduit mounting plate. Filtered drives can meet the class A limits of EN and EN Category 2 with this type of motor cable up to 10 meters.
Any external line filter should have its chassis connected to the drive chassis by mounting hardware or with the shortest possible wire or braid. The single and three phase models are illustrated herein. Refer to paragraph 3. Power remains present for up to 3 minutes on power input terminals L1, L2 and L3 and output terminals U, V and W even when the disconnect switch is in the OFF position.
Remove input power ahead of the drive and wait 3 minutes before removing the terminal cover. The The dynamic brake resistor connections for The digital inputs can be configured for active-high or active-low by setting the Assertion Level. Switch ALsw and P P is set to a value other than 0. When rotation direction is changed while the drive is running, the commanded direction LED will blink until the drive is controlling the motor in the selected direction.
Used for programming and can also be used as a reference for speed, PID setpoint, or torque setpoint. When the s and t buttons are the active reference, the middle LED on the left side of the display will be on. The CTRL pushbutton selects the start and speed reference control sources for the drive.
Press [ ] mode button to accept the new control mode selection. In the standard mode of operation, the drive frequency output is set directly by the selected reference keypad, analog reference, etc. P is displayed. Example: if P is set to 1, then diagnostic parameter P Software version is displayed.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions.
Enter a new password. SM4 Series Flux Vector. Safety information All safety information given in these Operating Instructions have the same layout: Signal Word! Warning of damage STOP!
0コメント