You can measure from floor plans, run one, etc. If you run one cable to each room from the distribution room, gently pull it out and make other cable run like it.
Then clear the path in the walls and drill holes. Once you have drilled the holes you can string out the cable and ensure no extra cable is tucked in the wall. After that, you can label cables on both ends and measure the exact cable length. Remember to leave spare cables for stripping and crimping. Now you need to wire the cables. Strip about one inch of the outer jacket off the cable and push the wires into the keystone jack to match the color code marked on it TA or TB standards.
Punch down the cables to keystone jacks or patch panel with a punch down tool. After you have all the cables connected, you can click the jacks into the wall plates. At last, fix the wall plate on the wall with supplied screws. You can refer to the video below for more details. Once all cables are wired, test the network with network cable tester. If LEDs on the tester light up, it means the Ethernet plug is connected correctly.
On the contrary, Ethernet plug is not connected right and you should check the Ethernet plug. After everything is prepared well, you can connect the network. Building a home network is very easy. This article talks about detailed steps of home Ethernet wiring. You will need a long mm — plus masonry drill bit, no smaller than 12mm diameter. Find out where the cable runs start and end.
There are cheap devices available which will plug into one end of a cable, send a tone down it, and allow it to be detected and the far end by another part of the device. Another odd phrase, much-searched, according to Google. We love cabling old houses as they present a challenge to us, and are satisfying to do well. Good engineers will trace everything anyway to avoid being misled by poorly-updated records. We also network with other similar engineers across the UK, so may be able to find one local to you.
Your email address will not be published. This site uses Akismet to reduce spam. Learn how your comment data is processed.
Facebook Twitter RSS. Submit a Comment Cancel reply Your email address will not be published. Install a structured wiring panel to keep your cables organized. Cables can just hang on the wall at the distribution point, but a wiring panel keeps them organized much better. If you want a wiring panel, purchase one from a hardware store. Then mount it in the wall section you just cut out. Then use a power drill to screw the box to both studs.
There are latches on the box to insert screws through. This job is easier with someone else holding the box up while you drill. A wiring panel is optional. If you want to save money, you don't have to buy one.
Part 3. Drill a 2. Use a boring drill bit 2. Press it against the ceiling plate and drill through it. Measure the distance from an external wall to the hole you drilled. This will help you find where to drill the attic hole if you can't find the point right above the distribution box. Drill a hole in your attic floor plate directly above the distribution panel. Go up to your attic and find the spot directly above where the distribution panel is.
Then use the same 2. If you can't find the distribution point, use the measurement you took when you drilled the first hole. Run your tape measure from the same external wall and find that distance in the attic. Drill at this point. If your attic has loose fiberglass insulation, wear a dust mask to avoid breathing in any particles.
While still in the attic, find the areas above rooms where you need cable access. Use the 2. The cables will exit the attic through these holes. Mark cutting holes in the rooms that the cables will feed into.
Then find the location where you want your cable outlet. Then use a ruler and draw a 2 in 5. Do this in each room that you need cable access in. Otherwise, locate them near an existing electrical outlet. Check for studs behind the wall before picking a location. Make sure you cut in an area with no studs. Cut out the box you drew on the wall. Use a drywall saw and cut through the lines you drew on the wall. Part 4. Since all cables feed outward from your distribution panel, mark each one so you remember its destination.
Wrap a piece of white tape around each wire. Use permanent marker and write where this cable feeds to. Labeling also makes repairs much easier. If a wire goes bad, you know right away which wire you should pull from the distribution box. Feed your cables up the wall into the attic space.
Feeding the wires up and down is usually a 2-person job. One person pushes the wire through the origin point and the other pulls through the hole at the destination point. Feed the wire through the hole above the distribution box while someone else pulls the from attic. Feed it down the hole from the attic until the person at the distribution box can grab it.
Then have them attach the wire to the end of the fish tape. Pull the fish tape up while the other person feeds the wire and work it through the hole in the attic. Work cables through the walls gently. Run the wires through the holes above their respective rooms. Then to the opposite action—have one person feed the cables down through the hole to the destination while another person pulls the cable out from the wall. Keep the wires out of the way by taping them to the ceiling rafters in the attic.
Do not staple them. Staples could damage the wires and also make replacing the wires difficult. Pull the cables through each wall outlet that you cut. Complete the cable installation by pulling each cable through the outlet holes you made. From here, you can run coaxial cables to your appliances or install an outlet for ethernet cables. These are available from hardware stores. Drew Hawkins1. It can vary from room to room, so start by figuring what you want in each room first.
Identify which rooms need a cable hookup. Usually, that'll be any room that will have a TV, landline phone, or computer. If you want to be on the safe side, you can run wires into every room, just in case you decide you want a cable hookup in another room later on.
0コメント